Toyota Avalon (XX50): Transmission Control Cable

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Drivetrain / P710 Hybrid Transmission / Transaxle / Transmission Control Cable

Adjustment

ADJUSTMENT

PROCEDURE

1. SECURE VEHICLE

(a) Fully apply the parking brake and chock a wheel.

CAUTION:

Make sure to apply the parking brake and chock a wheel before performing this procedure.
If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.

2. REMOVE CONSOLE BOX ASSEMBLY

Click here

3. ADJUST SHIFT LEVER POSITION

NOTICE:

Before adjusting the transmission control cable assembly, check that the shift lever position sensor and shift lever are in N.

(a) Disconnect the transmission control cable assembly from the transmission floor shift assembly.

(b) Slide the slider of the transmission control cable assembly in the direction indicated by the arrow in the illustration and pull the lock piece outward.

*a	Slider
*b	Lock Piece
*c	Slide
*d	Pull

NOTICE:

Check that the lock piece is pulled out.
Push the end of the transmission control cable assembly all the way to the base of the transmission floor shift assembly pin.
Connect the transmission control cable assembly so that the lock piece faces the driver side.

*a	Lock Piece
*b	Adjuster Case

(d) Push the lock piece into the adjuster case.

NOTICE:

Check that the shift lever position sensor and shift lever are in N.
Securely push in the lock piece until the slider lock is engaged.

*a	Lock Piece
*b	Push in
*c	Adjuster Case

(e) After adjusting the shift lever position, check the position and operation of the shift lever. If there is a problem, adjust the shift lever position again.

4. INSTALL CONSOLE BOX ASSEMBLY

Click here

Components

COMPONENTS

ILLUSTRATION

*1	COOL AIR INTAKE DUCT SEAL	*2	INLET AIR CLEANER ASSEMBLY
*3	NO. 1 ENGINE COVER SUB-ASSEMBLY	*4	AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
*5	FRONT LOWER NO. 1 FLOOR HEAT INSULATOR	*6	ENGINE ROOM MAIN WIRE
	Nm (kgfcm, ft.*lbf): Specified torque	-	-

ILLUSTRATION

*1	TRANSMISSION CONTROL CABLE ASSEMBLY	*2	NO. 1 CONSOLE BOX DUCT
	Nm (kgfcm, ft.*lbf): Specified torque	●	Non-reusable part

Installation

INSTALLATION

PROCEDURE

1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

(a) Turn the control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.

(b) Engage the 2 claws to install a new clip to the transmission control cable assembly.

(c) Using a screwdriver, engage the 4 claws and install the transmission control cable assembly to the No. 1 transmission control cable bracket.

NOTICE:

Make sure that the claws (A) of the clip are securely engaged in the grooves of the bracket.
Make sure that the transmission control cable assembly is securely installed inside of the claws (B) of the clip.

*1	Transmission Control Cable Assembly
*2	No. 1 Transmission Control Cable Bracket
*a	Claw (A)
*b	Claw (B)

(d) Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:

12 N·m {122 kgf·cm, 9 ft·lbf}

NOTICE:

Before installing the transmission control cable assembly, check that the shift lever position sensor and the shift lever are in N.

(e) Connect the transmission control cable assembly to the inverter with converter assembly with the 3 bolts.

Torque:

12 N·m {122 kgf·cm, 9 ft·lbf}

(f) Connect the transmission control cable assembly to the vehicle body with the 2 nuts.

Torque:

6.0 N·m {61 kgf·cm, 53 in·lbf}

(g) Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

Torque:

6.0 N·m {61 kgf·cm, 53 in·lbf}

2. CONNECT ENGINE ROOM MAIN WIRE

Click here

3. INSTALL NO. 1 CONSOLE BOX DUCT

(a) Install the No. 1 console box duct.

4. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

Click here

5. INSTALL FRONT LOWER NO. 1 FLOOR HEAT INSULATOR

(a) Install the front lower No. 1 floor heat insulator to the vehicle body with the 2 nuts.

Torque:

4.9 N·m {50 kgf·cm, 43 in·lbf}

6. INSTALL FRONT EXHAUST PIPE ASSEMBLY

Click here

7. INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Click here

8. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Click here

9. INSTALL INLET AIR CLEANER ASSEMBLY

Click here

10. INSTALL COOL AIR INTAKE DUCT SEAL

Click here

11. INSPECT SHIFT LEVER POSITION

Click here

12. ADJUST SHIFT LEVER POSITION

Click here

Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
Replacement of air fuel ratio sensor Gas leak from exhaust system is repaired	Inspection After Repair	Poor idle, etc. Engine start function, etc.

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

PROCEDURE

1. SECURE VEHICLE

(a) Fully apply the parking brake and chock a wheel.

CAUTION:

Make sure to apply the parking brake and chock a wheel before performing this procedure.
If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.

2. REMOVE COOL AIR INTAKE DUCT SEAL

Click here

3. REMOVE INLET AIR CLEANER ASSEMBLY

Click here

4. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Click here

5. REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Click here

6. REMOVE FRONT EXHAUST PIPE ASSEMBLY

Click here

7. REMOVE FRONT LOWER NO. 1 FLOOR HEAT INSULATOR

(a) Remove the 2 nuts and front lower No. 1 floor heat insulator from the vehicle body.

8. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY

Click here

9. REMOVE NO. 1 CONSOLE BOX DUCT

(a) Remove the No. 1 console box duct.

10. DISCONNECT ENGINE ROOM MAIN WIRE

Click here

11. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

(a) Move the shift lever to N.

(b) Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.

(c) Using a screwdriver, disengage the 4 claws and disconnect the transmission control cable assembly with the clip from the No. 1 transmission control cable bracket.

(d) Using a screwdriver, disengage the 2 claws and remove the clip from the transmission control cable assembly.

(e) Remove the 3 bolts and disconnect the transmission control cable assembly from the inverter with converter assembly.

(f) Remove the 2 nuts and disconnect the transmission control cable assembly from the vehicle body.

(g) Remove the 2 nuts and then remove the transmission control cable assembly from the vehicle body.

Shift Paddle Switch

Automatic Transaxle Assembly

See More:

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Sfi System: Engine Coolant Pump Circuit Short to Ground or Open (P26CA14). Engine Coolant Pump No Signal (P26CA31). Engine Coolant Pump Actuator Stuck (P26CB71)
Engine Coolant Pump Circuit Short to Ground or Open (P26CA14) DESCRIPTION Refer to DTC P26CA12. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note P26CA14 Engine Coolant Pump Circuit Short to Ground or Open The operation duty ratio (WPO) of the monitoring water in ...