Components
COMPONENTS
ILLUSTRATION
|
*1 | CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
*2 | LOWER INSTRUMENT PANEL FINISH PANEL LH |
|
*3 | LOWER INSTRUMENT PANEL FINISH PANEL RH |
*4 | CONSOLE BOX POCKET SUB-ASSEMBLY |
|
*5 | FRONT CONSOLE UPPER PANEL GARNISH |
*6 | REAR UPPER CONSOLE PANEL SUB-ASSEMBLY |
|
*7 | SHIFT LEVER KNOB SUB-ASSEMBLY |
- | - |
ILLUSTRATION
|
*1 | COMBINATION SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) |
- | - |
Inspection
INSPECTION
PROCEDURE
1. INSPECT COMBINATION SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
(a) Inspect the "NORMAL" or "NORMAL/CUSTOM" mode switch:
| (1) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
13 (B) - 16 (GND1) |
"NORMAL" or "NORMAL/CUSTOM" mode switch being pushed and held |
Below 1 Ω | |
"NORMAL" or "NORMAL/CUSTOM" mode switch not pushed |
10 kΩ or higher | If the result is not as specified, replace the combination switch (electric parking brake switch assembly). |
 |
|
*a | Component without harness connected
(Combination Switch (Electric Parking Brake Switch Assembly)) | | |
(b) Inspect the "SPORT" or "SPORT S/S+" mode switch:
| (1) Measure the resistance according to the value(s) in the table below.
Standard Resistance: |
Tester Connection | Condition |
Specified Condition | |
12 (P) - 16 (GND1) |
"SPORT" or "SPORT S/S+" mode switch being pushed and held |
Below 1 Ω | |
"SPORT" or "SPORT S/S+" mode switch not pushed |
10 kΩ or higher | If the result is not as specified, replace the combination switch (electric parking brake switch assembly). |
 |
|
*a | Component without harness connected
(Combination Switch (Electric Parking Brake Switch Assembly)) | | |
(c) Inspect the illumination:
| (1)
Apply battery voltage to the combination switch (electric parking brake
switch assembly) and check that the switch illuminates. OK: |
Condition | Specified Condition | |
Battery positive (+) → Terminal 3 (ILL+) Battery negative (-) → Terminal 7 (ILL-) |
Illuminates | If the result is not as specified, replace the combination switch (electric parking brake switch assembly). |
 |
|
*a | Component without harness connected
(Combination Switch (Electric Parking Brake Switch Assembly)) | | |
Installation
INSTALLATION
PROCEDURE
1. INSTALL COMBINATION SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
Click here 
2. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY
Click here
3. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
Click here
4. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here
5. INSTALL CONSOLE BOX POCKET SUB-ASSEMBLY
Click here
6. INSTALL FRONT CONSOLE UPPER PANEL GARNISH
Click here
7. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL RH
Click here
8. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH
Click here
Removal
REMOVAL
PROCEDURE
1. PRECAUTION
Click here 
2. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH
Click here
3. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL RH
Click here
4. REMOVE FRONT CONSOLE UPPER PANEL GARNISH
Click here
5. REMOVE CONSOLE BOX POCKET SUB-ASSEMBLY
Click here
6. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here
7. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
Click here
8. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY
Click here
9. REMOVE COMBINATION SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
Click here
