Toyota Avalon (XX50): Rear Axle Carrier

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual / Drivetrain / Axle And Differential / Rear Axle Carrier

Components

COMPONENTS

ILLUSTRATION

*A	for Gasoline Model	*B	for RH Side
*C	for LH Side	-	-
*1	NO. 1 FLOOR UNDER COVER	*2	NO. 2 FLOOR UNDER COVER
	Nm (kgfcm, ft.*lbf): Specified torque	-	-

ILLUSTRATION

*A	w/o AVS	-	-
*1	NO. 2 PARKING BRAKE WIRE ASSEMBLY	*2	REAR AXLE HUB AND BEARING ASSEMBLY
*3	REAR DISC	*4	REAR DISC BRAKE CALIPER ASSEMBLY
*5	REAR FLEXIBLE HOSE	*6	REAR DISC BRAKE DUST COVER SUB-ASSEMBLY
	Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": Nm (kgfcm, ft.*lbf)	-	-

ILLUSTRATION

*A	w/ AVS	-	-
*1	NO. 2 PARKING BRAKE WIRE ASSEMBLY	*2	REAR AXLE HUB AND BEARING ASSEMBLY
*3	REAR DISC	*4	REAR DISC BRAKE CALIPER ASSEMBLY
*5	REAR FLEXIBLE HOSE	*6	REAR DISC BRAKE DUST COVER SUB-ASSEMBLY
*7	WIRE HARNESS BRACKET	-	-
	Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": Nm (kgfcm, ft.*lbf)		Nm (kgfcm, ft.*lbf): Specified torque

ILLUSTRATION

*1	REAR AXLE CARRIER SUB-ASSEMBLY	*2	REAR COIL SPRING
*3	REAR FLEXIBLE HOSE BRACKET	*4	REAR LOWER COIL SPRING INSULATOR
*5	REAR NO. 1 SUSPENSION ARM ASSEMBLY	*6	REAR NO. 2 SUSPENSION ARM ASSEMBLY
*7	REAR SHOCK ABSORBER ASSEMBLY	*8	REAR STABILIZER LINK ASSEMBLY
*9	REAR UPPER CONTROL ARM ASSEMBLY	*10	REAR TRAILING ARM ASSEMBLY
*11	REAR STABILIZER BAR	*12	REAR SUSPENSION TOE ADJUST CAM SUB-ASSEMBLY
*13	NO. 2 CAMBER ADJUST CAM	*14	PLATE WASHER
	Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": Nm (kgfcm, ft.*lbf)	*	For use with a ball joint lock nut wrench

Installation

INSTALLATION

CAUTION / NOTICE / HINT

for HV Model:

When removing or installing the rear disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY

(a) Temporarily install the rear axle carrier sub-assembly to the rear shock absorber assembly with the nut and plate washer.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.

(b) Temporarily install the rear axle carrier sub-assembly to the rear upper control arm assembly with the bolt and nut.

NOTICE:

Insert the bolt with the threaded end facing the rear of the vehicle.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

Torque:

135 N·m {1377 kgf·cm, 100 ft·lbf}

2. INSTALL REAR FLEXIBLE HOSE BRACKET

(a) Install the rear flexible hose bracket to the rear axle carrier sub-assembly with the bolt.

Torque:

29 N·m {296 kgf·cm, 21 ft·lbf}

3. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

Click here

4. INSTALL REAR LOWER COIL SPRING INSULATOR

Click here

5. INSTALL REAR COIL SPRING

Click here

6. STABILIZE SUSPENSION

Click here

7. INSTALL REAR UPPER CONTROL ARM ASSEMBLY

(a) Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt.

Torque:

73 N·m {744 kgf·cm, 54 ft·lbf}

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

8. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

Click here

9. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

(a) Install the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) with the bolt.

Click here

10. INSTALL REAR SHOCK ABSORBER ASSEMBLY

Click here

11. INSTALL REAR STABILIZER LINK ASSEMBLY

Click here

12. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

Click here

13. INSTALL REAR DISC

Click here

14. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

Click here

15. INSTALL REAR FLEXIBLE HOSE

(a) Install the rear flexible hose to the rear flexible hose bracket with the bolt.

Torque:

29 N·m {296 kgf·cm, 21 ft·lbf}

16. INSTALL NO. 2 PARKING BRAKE WIRE ASSEMBLY (w/o AVS)

(a) Install the No. 2 parking brake wire assembly to the rear trailing arm assembly with the nut.

Torque:

15.5 N·m {158 kgf·cm, 11 ft·lbf}

(b) Engage the 2 clamps.

(d) Connect the No. 2 parking brake wire assembly connector to the rear axle hub and bearing assembly.

17. INSTALL NO. 2 PARKING BRAKE WIRE ASSEMBLY (w/ AVS)

(a) Install the No. 2 parking brake wire assembly to the rear trailing arm assembly with the nut.

Torque:

15.5 N·m {158 kgf·cm, 11 ft·lbf}

(b) Engage the clamp.

*a	Guide
*b	Clamp

(d) Install the nut.

Torque:

8.5 N·m {87 kgf·cm, 75 in·lbf}

(e) Engage the clamp and install the No. 2 parking brake wire assembly to the wire harness bracket.

(f) Connect the connector.

(g) Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.

(h) Connect the No. 2 parking brake wire assembly connector to the rear axle hub and bearing assembly.

18. INSTALL NO. 1 FLOOR UNDER COVER (for Gasoline Model)

(a) for RH Side:

Click here

19. INSTALL NO. 2 FLOOR UNDER COVER (for Gasoline Model)

(a) for LH Side:

Click here

20. INSTALL REAR WHEEL

Click here

21. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

(a) Install the rear No. 2 suspension arm assembly (rear suspension member sub-assembly side) with the nut.

Click here

22. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)

(a) Connect the reservoir level switch connector.

(b) Connect the cable to the negative (-) auxiliary battery terminal.

Click here

(d) Depress the brake pedal and release it.

(e) Clear the DTCs.

Click here

23. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Click here

24. CHECK FOR SPEED SENSOR SIGNAL

for HV Model: Click here

for Gasoline Model: Click here

25. PERFORM INITIALIZATION

for Gasoline Model:

Intelligent Clearance Sonar System
Intuitive Parking Assist System

Parking Assist Monitor System

for Initialization

for Calibration

Panoramic View Monitor System

for Initialization

for Calibration

for HV Model:

Intelligent Clearance Sonar System
Intuitive Parking Assist System

Parking Assist Monitor System

for Initialization

for Calibration

Panoramic View Monitor System

for Initialization

for Calibration

Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle carrier sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
Rear wheel alignment adjustment	Perform system variant learning and acceleration sensor zero point calibration.	VSC disabled or malfunctioning DTCs are output Slip indicator light illuminated ABS warning light illuminated
Suspension, tires, etc. (The vehicle height changes because of suspension or tire replacement.)	Measure ultrasonic sensor detection angle Ultrasonic sensor detection angle registration	Intelligent Clearance Sonar System Intuitive Parking Assist System
	Rear television camera assembly optical axis adjustment (Back camera position setting)	Parking Assist Monitor System	for Initialization for Calibration
	Parking assist ECU initialization Adjust steering angle Television camera assembly optical axis adjustment (Back camera position setting)	Panoramic View Monitor System	for Initialization for Calibration

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
*: When performing learning using the Techstream. Click here
Auxiliary battery terminal is disconnected/reconnected	Perform steering sensor zero point calibration	Lane Departure Alert System (w/ Steering Control)
		Pre-collision System
		Intelligent Clearance Sonar System*
		Lighting System (for HV Model with Cornering Light)
	Memorize steering angle neutral point	Parking Assist Monitor System
	Memorize steering angle neutral point	Panoramic View Monitor System
Rear wheel alignment adjustment	Clear zero point calibration data. Perform yaw rate and acceleration sensor zero point calibration.	DTCs are stored ABS warning light illuminates Brake warning light / yellow (minor malfunction) illuminates Slip indicator light illuminates VSC disabled or malfunctions
Suspension, tires, etc. (The vehicle height changes because of suspension or tire replacement.)	Measure ultrasonic sensor detection angle Ultrasonic sensor detection angle registration	Intelligent Clearance Sonar System Intuitive Parking Assist System
	Rear television camera assembly optical axis adjustment (Back camera position setting)	Parking Assist Monitor System	for Initialization for Calibration
	Parking assist ECU initialization Adjust steering angle Television camera assembly optical axis adjustment (Back camera position setting)	Panoramic View Monitor System	for Initialization for Calibration

for HV Model:

When removing or installing the rear disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION (for HV Model)

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

2. DISABLE BRAKE CONTROL (for HV Model)

Click here

3. REMOVE REAR WHEEL

Click here

4. REMOVE NO. 2 FLOOR UNDER COVER (for Gasoline Model)

(a) for LH Side:

Click here

5. REMOVE NO. 1 FLOOR UNDER COVER (for Gasoline Model)

(a) for RH Side:

Click here

6. SEPARATE NO. 2 PARKING BRAKE WIRE ASSEMBLY (w/o AVS)

(a) Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

NOTICE:

Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.
Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.

(b) Using a screwdriver with its tip wrapped with protective tape, disconnect the No. 2 parking brake wire assembly connector from the rear axle hub and bearing assembly.

NOTICE:

Be careful not to damage the rear axle hub and bearing assembly or connector cover.

*a	Protective Tape

(c) Remove the nut, disengage the 2 clamps and separate the No. 2 parking brake wire assembly from the rear flexible hose bracket and rear trailing arm assembly.

7. SEPARATE NO. 2 PARKING BRAKE WIRE ASSEMBLY (w/ AVS)

(a) Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

NOTICE:

Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.
Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.

(b) Using a screwdriver with its tip wrapped with protective tape, disconnect the No. 2 parking brake wire assembly connector from the rear axle hub and bearing assembly.

NOTICE:

Be careful not to damage the rear axle hub and bearing assembly or connector cover.

*a	Protective Tape

(d) Remove the nut and disengage the clamp.

(e) Remove the nut, disengage the clamp and separate the No. 2 parking brake wire assembly from the rear flexible hose bracket and rear trailing arm assembly.

8. SEPARATE REAR FLEXIBLE HOSE

(a) Remove the bolt and separate the rear flexible hose from the rear flexible hose bracket.

9. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

Click here

10. REMOVE REAR DISC

Click here

11. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY

Click here

12. REMOVE REAR FLEXIBLE HOSE BRACKET

(a) Remove the bolt and rear flexible hose bracket from the rear axle carrier sub-assembly.

13. REMOVE REAR STABILIZER LINK ASSEMBLY

Click here

14. REMOVE REAR COIL SPRING

Click here

15. REMOVE REAR LOWER COIL SPRING INSULATOR

Click here

16. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY

Click here

17. REMOVE REAR AXLE CARRIER SUB-ASSEMBLY

(a) Loosen the 2 bolts of the rear trailing arm assembly.

(b) Loosen the nut of the rear shock absorber assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.

*1	Rear Axle Carrier Pin

NOTICE:

When jacking up the rear axle carrier sub-assembly, be sure to jack it up slowly.
Make sure to perform this operation with the vehicle kept as low as possible.

*a	Wooden Block
*b	Jack

(d) Loosen the bolt (A).

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.

(e) Remove the 2 bolts and separate the rear trailing arm assembly from the rear axle carrier sub-assembly.

(f) Remove the nut and plate washer, and separate the rear shock absorber assembly from the rear axle carrier sub-assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.

(g) Remove the bolt (A), nut and rear axle carrier sub-assembly from the rear upper control arm assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.

Front Axle Hub

Rear Axle Hub Bolt

See More:

Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Audio And Visual System(for Gasoline Model): USB Device Malfunction (B1585). Black Screen. Camera ECU Malfunction (C1610)
USB Device Malfunction (B1585) DESCRIPTION This DTC is stored when a malfunction occurs in a connected device. DTC No. Detection Item DTC Detection Condition Trouble Area B1585 USB Device Malfunction When any of the following conditions is met: A non mass-storage class or incompatible protocol USB d ...